banner



Home  ›  How To Remove Harmonic Balancer Bolt Toyota

How To Remove Harmonic Balancer Bolt Toyota

Written By Thursday, April 21, 2022 Add Comment Edit

  1. How to scissure a harmonic balancer bolt??

    Hey guys,

    I have been trying to remove the harmonic balancer bolt for about two hours now.

    I accept used a i/2" Drive Rattle Gun on information technology for about 1 hour and and so tried a billow bar and using the starter motor to cleft it, but still no luck and now the battery is going flat.

    Does any one else have whatever idea??

    Vehicle is a 100 series Landcruiser with a four.5L six.

    The people at Toyota service said it may have had excessive loktite put on when the engine was congenital as it usually only takes 1 or two goes using the starter motor to crevice it.

    Any assist would be appreciated.

    Thanks

    Steve

  2. Re: How to scissure a harmonic balancer commodities??

    an extremely large breaker bar, if you only have a short ane get a long strong pipe to put over the handle.

    simply demand to crack information technology and then can get to the ratchet.

    PS oh you are turning information technology the right fashion ?

    Final edited past VX2VESS; 27-02-2009 at 12:37 PM.

  3. Re: How to crack a harmonic balancer commodities??

    Did I mention the head is off and in that location is no pinch??

  4. Re: How to crack a harmonic balancer bolt??

    Quote Originally Posted by Steve-LS2 View Post

    Did I mention the head is off and there is no compression??

    you need to lock the motor via the flywheel.

    tin try park if auto or in gear for manual if the gearbox is nonetheless on, amend to lock the flywheel even so

    if you cannot get to the flywheel anywhere accept the starter out, spose you don't have the tool to lock the flywheel either?

    Last edited by VX2VESS; 27-02-2009 at 12:43 PM.

  5. Re: How to crack a harmonic balancer commodities??

    Tried using any heat on it? Locktite doesn't like heat, if that is the problem.

  6. Re: How to fissure a harmonic balancer commodities??

    Thanks, will put it in park and give it a get

    no die, put it in park, still turns costless, tried drive and low range and withal moves without restriction.

    Anyone know any other way of stopping the engine from spinning?

    Thanks

    Steve

    Quote Originally Posted past Souljah View Post

    Tried using whatever heat on it? Locktite doesn't like oestrus, if that is the problem.

    Hey Souljah, I was told to use an oxy on it but I don't have one at home.

    Does anyone know of something to heat the bolt with?

    Cheers

    Steve

    Last edited by Steve-LS2; 27-02-2009 at 12:47 PM. Reason: Automerged Doublepost

  7. Re: How to crack a harmonic balancer bolt??

    has worked in the past occasionally, simply the convertor to spin merely sometimes its enough.

    oh well you have to practise it the correct way lock the flywheel up and so it can't turn.

    oh one more way, does the balancer accept holes in information technology that you can put a thick bar of screwdriver through and lock it against the chassis or something to stop information technology turning?

    could buy one of those gas cans with blowtorch on the end from the hardware store to estrus it. simply once you fix the motor from turning it should crack with a large bar and some effort.

    had a few that actually suck, including this ls1, it was really tight all the mode out. lucky i had a ane mtr Snap On billow bar to utilise.

    Last edited by VX2VESS; 27-02-2009 at 12:59 PM.

  8. Re: How to crack a harmonic balancer commodities??

    Quote Originally Posted past vt2vx View Post

    has worked in the by oh well you have to do it the right way lock the flywheel up so information technology tin can't turn

    Anyone know how to do that?

  9. Re: How to scissure a harmonic balancer bolt??

    Bolt a piece of plate beyond the height of the block, jam some rag in between piston and plate????

  10. Re: How to cleft a harmonic balancer bolt??

    Quote Originally Posted by vt2vx View Post

    oh one more fashion, does the balancer take holes in information technology that you can put a thick bar of screwdriver through and lock it against the chassis or something to stop it turning?

    It has bolt holes for the puller, I already tried to practise that simply aptitude the bolt...

    Don't want to try once more incase I break something else....

  11. Re: How to scissure a harmonic balancer bolt??

    Quote Originally Posted by Steve-LS2 View Post

    It has bolt holes for the puller, I already tried to do that but bent the bolt...

    Don't want to try over again incase I suspension something else....


    also small for that need bigger holes.

    if y'all have someone to help take the starter out and use a monster size screwdriver to agree the flywheel, non ideal method just if you don't have the tool for it it may work, danger is snapping of a flywheel molar only holding one tooth.

  12. Re: How to scissure a harmonic balancer commodities??

    Ordinarily the starter should practice the flim-flam, unless the bombardment is a bit soft.

    I wouldn't use heat as the adventure of over heating is possible. The balancer is not designed to get likewise hot and over heating it can crusade the bonded rubber to separate. I also would not gamble using a piston to lock the motor. the bearings are not meant to see that sort of forcefulness without an oil film to protect them.

    Locking the fly wheel is usually done by dropping the starter and bolting in a piece of metallic designed to engage the band gear. You lot can do it with a small "jimmy" bar if you have someone to hold information technology for you when you try the bolt via the "Large" breaker bar. If the starter method isn't going to work, then locking the crank is the only other selection, either via the ring gear, or via the balancer spokes.

    I take a one-half decent Sidchrome 1/ii" breaker bar, et me know if you desire to borrow it.

    Simon

  13. Re: How to crevice a harmonic balancer bolt??

    I call up I'm pretty fukced, I think I may demand to get information technology towed to a mechanic to get it done properly.

    Can anyone in Melbourne come over and help on the weekend???

    Thanks

    Steve

    Quote Originally Posted by swingtan View Post

    Normally the starter should do the fob, unless the bombardment is a chip soft.

    I wouldn't utilize estrus as the chance of over heating is possible. The balancer is not designed to go as well hot and over heating it can cause the bonded safety to separate. I too would non take chances using a piston to lock the motor. the bearings are non meant to see that sort of force without an oil motion picture to protect them.

    Locking the fly wheel is usually done past dropping the starter and bolting in a piece of metal designed to engage the ring gear. You can do it with a small "jimmy" bar if you have someone to hold it for you when you attempt the bolt via the "Big" breaker bar. If the starter method isn't going to work, then locking the crank is the just other selection, either via the ring gear, or via the balancer spokes.

    I have a half decent Sidchrome ane/2" billow bar, et me know if y'all desire to borrow information technology.

    Simon

    Hi Simon,

    I'm upwardly for anything at the moment, I have already spent over 2K to fix this and don't really want to spend much more.

    Don't actually wanna drib the starter out only if I have no other option then I guess this is the but thing.

    What happens if I bust some teeth off the band gear??

    Thanks

    Steve

    Last edited by Steve-LS2; 27-02-2009 at 01:10 PM. Reason: Automerged Doublepost

  14. Re: How to fissure a harmonic balancer bolt??

    tried a search on the right tool for you to use, they are usually a little toothed gismo that bolts into the starter motor hole to hold the flywheel.

    yet found this idea, information technology might work well

    Quote Originally Posted by Steve-LS2 View Post

    I call up I'm pretty fukced, I think I may need to get it towed to a mechanic to get it done properly.

    Can anyone in Melbourne come up over and help on the weekend???

    Cheers

    Steve

    What happens if I bust some teeth off the band gear??

    Thanks

    Steve

    don't ask that, normally the flywheel tool holds a few teeth at once which is much safer.
    Last edited by VX2VESS; 27-02-2009 at 01:14 PM. Reason: Automerged Doublepost

  15. Re: How to scissure a harmonic balancer bolt??

    Quote Originally Posted by vt2vx View Post

    tried a search on the right tool for yous to employ, they are usually a piddling toothed gismo that bolts into the starter motor hole to concur the flywheel.

    all the same plant this idea, it might piece of work well

    don't ask that, normally the flywheel tool holds a few teeth at in one case which is much safer.

    If only I could find a tool like that!!

    Thanks VT, you've been very helpful, only I think I accept reached the limit of my mechanical abilities.

How To Remove Harmonic Balancer Bolt Toyota,

Source: http://www.ls1.com.au/forum/showthread.php?t=114735

Posted by: dickinsongoodue.blogspot.com

0 Response to "How To Remove Harmonic Balancer Bolt Toyota"

Post a Comment

Subscribe to: Post Comments (Atom)

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel